Search found 190 matches

by katellwood
Sat Sep 28, 2019 3:34 pm
Forum: Woodworking
Topic: Hipped roof pitch help please
Replies: 4
Views: 852

Re: Hipped roof pitch help please

These may help
roof geometry 1.jpg
roof geometry 3.jpg
Plumb/foot cuts on both rafters and jack rafters are the same
by katellwood
Wed Apr 17, 2019 11:06 am
Forum: Projects
Topic: driveway gates
Replies: 26
Views: 6137

Re: driveway gates

you would create a haunch in a wide tenon more to strengthen the mortice as in certain cases the mortice walls are thin and need bolstering in the middle this is purely subjective to the thickness of the material. In my case with six inch rails and 60mm+ thickness of material a central haunch in my ...
by katellwood
Tue Apr 09, 2019 8:44 pm
Forum: Projects
Topic: driveway gates
Replies: 26
Views: 6137

Re: driveway gates

Haunching is usually carried out on a corner joint say the top and bottom rail of a door so as to completely contain the tenon in the mortice, on wide rails (usually middle rails) the haunch is usually in the middle of the rail thereby preventing the need for an overlong mortice. The short tenon on ...
by katellwood
Sun Apr 07, 2019 6:33 pm
Forum: Projects
Topic: driveway gates
Replies: 26
Views: 6137

Re: driveway gates

bit of a wet day but just been out to take a few photo's https://i.imgur.com/5NjHUe9.jpg https://i.imgur.com/KcZlNsO.jpg absolutely no sagging of the gates or movement on the posts the only issue which does not concern me too much is that the auto closers needed to be place high up to so as to go ab...
by katellwood
Sat Mar 02, 2019 9:02 pm
Forum: Power Tools and Machinery
Topic: Saw blades for Radial Arm Saws
Replies: 5
Views: 962

Re: Saw blades for Radial Arm Saws

I would suggest you need a crosscut blade with chip limiters (this restricts how much material each tooth takes during the cut and prevent ride up)
by katellwood
Tue Feb 05, 2019 11:09 pm
Forum: Woodworking
Topic: Replacement Sash and Case Windows
Replies: 62
Views: 7594

Re: Replacement Sash and Case Windows

Rich

With a felder you will need a minimum of a chip extractor as the cutters will block up and seriously effect the timber finish. modern machines are designed to work with extraction as they throw all the spoil in the direction of a 100/125mm pipe
by katellwood
Tue Feb 05, 2019 1:54 pm
Forum: Woodworking
Topic: Replacement Sash and Case Windows
Replies: 62
Views: 7594

Re: Replacement Sash and Case Windows

Hi You would not go far wrong with this (or something like) at the right price https://www.ebay.co.uk/itm/FELDER-BF6-26-Combination-Woodworking-Machine-on-360-degree-turntable-240-v/273681270438?hash=item3fb8acc6a6:g:G~gAAOSw7C5cVDNl:rk:1:pf:1&frcectupt=true I'm on my third combi the last two being ...
by katellwood
Thu Jan 24, 2019 8:22 pm
Forum: Woodworking
Topic: Marks on wood door
Replies: 5
Views: 1009

Re: Marks on wood door

oxalic acid powder (which you dissolve in warm water) or liberon wood bleacher (which is prepared oxalic acid)
by katellwood
Fri Dec 28, 2018 2:04 pm
Forum: Power Tools and Machinery
Topic: Hammer C3-31 dished fence
Replies: 23
Views: 3650

Re: Hammer C3-31 dished fence

Glad to be of help.

Its good that we can all learn from each other, its what forums are for
by katellwood
Thu Dec 27, 2018 4:33 pm
Forum: Power Tools and Machinery
Topic: Table Saw (£400 budget)
Replies: 8
Views: 1953

Re: Table Saw (£400 budget)

just my two penneth If you are cutting full sized sheets (8 x 4) on a £400 table saw you are going to struggle and the initial cuts will not be very accurate. I also use a Felder with a sliding table however for the initial cuts I start with a dewalt track saw and a 2.7m track. Its far easier to car...
by katellwood
Mon Dec 17, 2018 6:53 pm
Forum: Power Tools and Machinery
Topic: Hammer C3-31 dished fence
Replies: 23
Views: 3650

Re: Hammer C3-31 dished fence

Thanks for the link to that thread which I missed first time round. I'm going to look forward to reading that. It's a good tip but had you thought of a power feeder on your planer ? This is mine with a 4.4m length of timber being prepped for skirting. (bottom LH corner) https://farm5.staticflickr.c...
by katellwood
Sun Dec 16, 2018 10:30 pm
Forum: Power Tools and Machinery
Topic: Hammer C3-31 dished fence
Replies: 23
Views: 3650

Re: Hammer C3-31 dished fence

I'm on my third combination machine and my second Felder and whilst I can see the point of some of the above comments and essentially agree I run a combi due to workshop size That being said and being a one man band one advantage I have exploited is the use of a long sliding table with the spindle. ...
by katellwood
Sat Oct 20, 2018 11:17 am
Forum: Power Tools and Machinery
Topic: Silicon Spray
Replies: 3
Views: 1050

Re: Silicon Spray

Wax polish works for me, also keeps them slick
by katellwood
Wed Jul 18, 2018 10:38 am
Forum: Wanted
Topic: Whitehill Block (old style)
Replies: 7
Views: 2280

Re: Whitehill Block (old style)

this picture may help https://i.imgur.com/MGJbbdT.jpg Because the cutter is further away from the centre line of the block when the cutter is 90 degrees to the fence then when it hits the timber it hits it at more of an acute angle so for example if cutting a quarter round then in height from the be...
by katellwood
Wed Jul 18, 2018 1:58 am
Forum: Wanted
Topic: Whitehill Block (old style)
Replies: 7
Views: 2280

Re: Whitehill Block (old style)

One final thing, because the cutter is mounted further away from the centre than modern pinned blocks the shape of the cutter will not be the same as the moulding produced
by katellwood
Wed Jul 18, 2018 1:45 am
Forum: Wanted
Topic: Whitehill Block (old style)
Replies: 7
Views: 2280

Re: Whitehill Block (old style)

don't want to teach you how to suck eggs however if you have not used these blocks before a couple of tips if I may. I assume you are using a pair of cutters, balance is important with these blocks so getting the two cutters in place accurately is important. I use an L shaped ply slip drawing around...
by katellwood
Mon Jul 16, 2018 8:43 pm
Forum: Wanted
Topic: Whitehill Block (old style)
Replies: 7
Views: 2280

Re: Whitehill Block (old style)

they appear on ebay from time to time (i think you just missed one) however if you want I could lend you one (believe you are in Kent)
by katellwood
Sun Jun 17, 2018 3:29 pm
Forum: Woodworking
Topic: Rubbing down solid oak door - how far?
Replies: 2
Views: 918

Re: Rubbing down solid oak door - how far?

Try cleaning it off with some oxalic acid diluted with warm water, that should get rid of any black marks and revive the timber.

You then need to neutralise with water, let it dry and cut back the raised grain prior to finishing
by katellwood
Thu May 03, 2018 4:28 pm
Forum: Projects
Topic: driveway gates
Replies: 26
Views: 6137

Re: driveway gates

An update too this. I appreciate there has been a delay in getting these swinging, the main reason being I spent the majority of the winter in Australia and if I had hung them prior to going I would not have been able to monitor any movement in the boards and take any remedial action as needed. Anyw...
by katellwood
Thu Jan 04, 2018 2:01 pm
Forum: Woodworking
Topic: Replicating square balusters
Replies: 1
Views: 1076

Re: Replicating square balusters

This is the only cost effective way of replicating square balusters I know of, however pretty specialist

https://www.instagram.com/p/BQ0COylguCq ... d=therming

You could try Richard Findley
by katellwood
Fri Dec 22, 2017 7:25 pm
Forum: Projects
Topic: driveway gates
Replies: 26
Views: 6137

Re: driveway gates

Thanks for all the nice comments/constructive criticisms and advice, its all very much appreciated. Where we are at the moment is, I have had delivered two pair of 900mm adjustable hooks and bands. They were advertised as being galvanised and powder coated however the coating was flaking a little (d...
by katellwood
Thu Dec 21, 2017 9:25 pm
Forum: Woodworking
Topic: Timbmet...................
Replies: 5
Views: 1804

Re: Timbmet...................

Have been to JW timber a few times, unfortunately they no longer supply AW oak just European, however for service I cannot fault them. The last lot of Oak I bought(What i built the gates from here http://www.woodworkuk.co.uk/forum/viewtopic.php?f=9&t=13444) was from http://oakandwood.co.uk/ They do ...
by katellwood
Tue Dec 19, 2017 10:07 pm
Forum: Woodworking
Topic: Timbmet...................
Replies: 5
Views: 1804

Re: Timbmet...................

Aren't Timbmet now owned by Meyers??? There used to be a Meyers close to me in Strood, Kent, that closed. I then started using Timbmet in Larkfield, Kent and on being taken over they closed that branch. Being a one man band with limited storage I only collect materials, don't have anything large del...
by katellwood
Mon Dec 11, 2017 10:11 pm
Forum: Projects
Topic: driveway gates
Replies: 26
Views: 6137

Re: driveway gates

davidpidge wrote:Fantastic WIP photos. They are some monster bits of joinery! How are you moving them around?
I'm not at the moment. they were just about manageable prior to boarding however now boarded I need someone to help me move them about.
by katellwood
Mon Dec 11, 2017 10:08 pm
Forum: Projects
Topic: driveway gates
Replies: 26
Views: 6137

Re: driveway gates

Very impressive matey. The only thing I would be concerned with is the expansion gap between the boards. From personal experience I don’t think that 1.5mm will be enough - I’d have gone for 3mm and treated them before assembly. I hope I’m wrong as they really do look the business. Yes that's someth...
by katellwood
Mon Dec 11, 2017 9:17 pm
Forum: Projects
Topic: driveway gates
Replies: 26
Views: 6137

driveway gates

Driveway Gates I’ve just completed a pair of driveway gates. These are for myself and are part of a long ongoing project whereby I have created a new driveway. This has included digging out a few tons of earth, laying brick retaining walls which included elements of curved brickwork, laying approx 1...
by katellwood
Mon Dec 04, 2017 10:55 am
Forum: Power Tools and Machinery
Topic: cutting straight with a bandsaw
Replies: 15
Views: 3604

Re: cutting straight with a bandsaw

Stenner Band-Re-saw would cut through this in about one minute your Bandsaw 20+ I'd say.............? Stenners I've seen approx 10-20 secs for an 8' length my setup 2-3 mins 2-3 minutes is Much quicker than I thought. Perhaps I should buy some blades like you as I have some odd blocks of oak that I...
by katellwood
Mon Dec 04, 2017 10:44 am
Forum: Power Tools and Machinery
Topic: cutting straight with a bandsaw
Replies: 15
Views: 3604

Re: cutting straight with a bandsaw

Image

Image

hope this helps
by katellwood
Sun Dec 03, 2017 11:51 pm
Forum: Power Tools and Machinery
Topic: cutting straight with a bandsaw
Replies: 15
Views: 3604

Re: cutting straight with a bandsaw

Nearly right, its this one http://www.ikea.com/gb/en/products/lighting/work-lamps/jansj%C3%B6-led-work-lamp-black-art-00169659/ I've replaced the supplied weighted base with a piece of timber and super-glued two 25mm rare earth magnets into the new base. Works a treat and rock solid, stays where you...
by katellwood
Sun Dec 03, 2017 12:40 pm
Forum: Power Tools and Machinery
Topic: cutting straight with a bandsaw
Replies: 15
Views: 3604

Re: cutting straight with a bandsaw

The attached was resawing kiln dried 6" and 8" euro oak 8' long. the machine is a Meber 500 with a approx 20" throat and 12" depth of cut, single phase with a 2hp motor. https://i.imgur.com/JrdsWth.jpg As you can see I used supports both front and rear which are essential for this type of cutting (...
by katellwood
Sun Dec 03, 2017 11:27 am
Forum: Power Tools and Machinery
Topic: cutting straight with a bandsaw
Replies: 15
Views: 3604

Re: cutting straight with a bandsaw

The attached was resawing kiln dried 6" and 8" euro oak 8' long. the machine is a Meber 500 with a approx 20" throat and 12" depth of cut, single phase with a 2hp motor. https://i.imgur.com/JrdsWth.jpg As you can see I used supports both front and rear which are essential for this type of cutting (e...
by katellwood
Wed Oct 04, 2017 1:03 pm
Forum: Woodworking
Topic: British Carpenters Jargon
Replies: 11
Views: 3028

Re: British Carpenters Jargon

How about, "gun-stop joint" , that's a pearl for you. It's a diminishing joint in the middle rail/stile of a door. Levelle r is the man to explain the joint to you, but he has not yet entered this thread. Mark In the absence of leveller and if I may, its actually known as a gunstock stile (as the s...
by katellwood
Tue Aug 22, 2017 10:49 pm
Forum: Woodworking
Topic: Iroko Worktop
Replies: 11
Views: 2642

Re: Iroko Worktop

I've used both PU and Titebond 3 on iroko worktops successfully.

One suggestion is to wipe the joints with thinners then let it evaporate prior to gluing, this should remove any oils contained in the timber which could affect the adhesives abilities
by katellwood
Fri Jun 30, 2017 6:58 pm
Forum: Power Tools and Machinery
Topic: Felder BF5 planer bearings
Replies: 7
Views: 2394

Re: Felder BF5 planer bearings

PM sent
by katellwood
Mon May 08, 2017 10:39 pm
Forum: Power Tools and Machinery
Topic: Looking to buy a Felder BF5-26....
Replies: 24
Views: 5556

Re: Looking to buy a Felder BF5-26....

How about this just to keep you interested until you find what you want: http://www.ebay.co.uk/itm/LUREM-C-210B-Universal-Woodworker/132182973056?_trksid=p2047675.c100005.m1851&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D2%26asc%3D43782%26meid%3Daf6a6de638894ccaaf5a2ffd3387f69d%26pid%3D100005%26...
by katellwood
Sun Apr 30, 2017 7:14 pm
Forum: Power Tools and Machinery
Topic: Looking to buy a Felder BF5-26....
Replies: 24
Views: 5556

Re: Looking to buy a Felder BF5-26....

they're the movement lengths generated by the different sizes of sliding table
by katellwood
Sun Apr 30, 2017 3:18 pm
Forum: Power Tools and Machinery
Topic: Looking to buy a Felder BF5-26....
Replies: 24
Views: 5556

Re: Looking to buy a Felder BF5-26....

This is mine http://i243.photobucket.com/albums/ff239/katellwood/Mobile%20Uploads/20170430_150156_zps7xrlc7qp.jpg And where I keep the outrigger http://i243.photobucket.com/albums/ff239/katellwood/Mobile%20Uploads/20170430_150254_zps2tyskdh5.jpg Be aware though my model is now only sold as a 741 wit...
by katellwood
Sun Apr 30, 2017 2:15 pm
Forum: Power Tools and Machinery
Topic: Looking to buy a Felder BF5-26....
Replies: 24
Views: 5556

Re: Looking to buy a Felder BF5-26....

I had a Bf5 although with the 12" planer I think there are two versions, one where the tilt on the spindle and saw is changed with a lever (and light taps with a lump of wood for fine adjustment) and one with wheel adjustment. Great bit of kit only changed it when I upgraded to a Cf731 and still sol...
by katellwood
Sat Oct 22, 2016 8:16 pm
Forum: Projects
Topic: Table top
Replies: 3
Views: 2002

Re: Table top

Steve

How was the Osmo on the Iroko?

I've had problems with their worktop oil not drying on Iroko and after a little bit of research discovered that ordinary Osmo is not suitable for dense tropical hardwoods like Iroko

They produce a thinner version for tropicals which I now use on Iroko

TIA