Search found 182 matches: Wealden

Searched query: wealden

by Leveller2911
Wed Jun 07, 2017 10:01 pm
Forum: Woodworking
Topic: Early Sash Window / Shutters RESEARCH
Replies: 55
Views: 2193

Re: Early Sash Window / Shutters RESEARCH

... it works really well and as long as you allow for paint its really good. On the meeting rails I use mighton brush in the same carrier.... I think Wealden tools do a router cutter which is 7mm wide and you get 3 different bearing guides so you can vary the depth the bubble carrier is routered in ...
by Recont
Sun May 21, 2017 5:24 pm
Forum: Power Tools and Machinery
Topic: Various Power Tools Recommendations
Replies: 2
Views: 139

Re: Various Power Tools Recommendations

Welcome to the forum. Hitachi 1/2" routers are quite cheap new - you might be lucky with a 2nd hand one but it might be a dog. Try wealden tools for bits. If you buy a router plate, you can make a simple router table - I think Wealden sell them or the likes of Axminster or Rutlands. ...
by promhandicam
Sun May 21, 2017 5:12 pm
Forum: Power Tools and Machinery
Topic: Various Power Tools Recommendations
Replies: 2
Views: 139

Re: Various Power Tools Recommendations

Welcome to the forum. Hitachi 1/2" routers are quite cheap new - you might be lucky with a 2nd hand one but it might be a dog. Try wealden tools for bits. If you buy a router plate, you can make a simple router table - I think Wealden sell them or the likes of Axminster or Rutlands. If ...
by Doug
Sat Oct 29, 2016 5:40 pm
Forum: For Sale
Topic: SPINDLE MOULDER TOOLING - ALL SOLD
Replies: 3
Views: 518

Re: SPINDLE MOULDER TOOLING

I'd like the

150 x 4 - 15 x 30 Wealden shim adjustable groover 45mm groove depth F431250 £100


2 pairs straight cut
1 pair each of nos. 83, 84, 106, 171, 173, 174, 175, 176

and a pair of 55mm knives and limiters with 22mm radius

£50 for the lot

Do you want bank transfer?
by tusses
Sat Oct 15, 2016 10:09 am
Forum: Woodworking
Topic: Concave.
Replies: 6
Views: 647

Re: Concave.

... all the nest boxes had flat bottoms. Nesting material stopped the eggs rolling about the only thing I can think of similar, is where the seed was. wealden do various bits depending on your budget http://www.wealdentool.com/acatalog/Online_Catalogue_Dished_Panel_Mould_85.html http://www.wealdentool.com/acatalog/Online_Catalogue_Coved_Upstand_226.html ...
by nickw
Tue Sep 06, 2016 9:57 am
Forum: Woodworking
Topic: Advice: Asymmetric (centre?) bead in skirting
Replies: 3
Views: 532

Re: Advice: Asymmetric (centre?) bead in skirting

... be the most cost effective way of achieving this. To do it with router will require a router table setup - if you have one then take a look at Wealden's mini mould cutters, they might be able to do what you want. As well as the cutter you will need to buy an arbor. http://www.wealdentool.com/cgi-bin/sh000001.pl?REFPAGE=http%3a%2f%2fwww%2ewealdentool%2ecom%2f&WD=mini%20mould&PN=Online_Catalogue_Mini_Mould_Bead_Mould_254%2ehtml%23aT3413#aT3413
by nickw
Sat Jul 30, 2016 1:24 pm
Forum: Power Tools and Machinery
Topic: Have cash, need tooling.
Replies: 3
Views: 516

Re: Have cash, need tooling.

Suppliers:
Wealden
Whitehill

What to buy:
If you're a pro buy stuff as and when you have a need for it.
If you're an amateur buy stuff until you run out of credit.

That's how it works, isn't it? :-D
by Bighat
Sun Feb 28, 2016 11:07 pm
Forum: Woodworking
Topic: Where do I buy a "Leigh Jig Guide Bush"
Replies: 13
Views: 1054

Re: Where do I buy a "Leigh Jig Guide Bush"

Don't bother withe the Leigh specific guide Bush, just order a 7/16 guide bush from wealden tools, they are the same. If you have standard dewalt/elu spacing on your router you won't even need an adaptor, though I'm not sure what Hitachi use. Plus wealden will get it to you next day.
by old2
Fri Feb 05, 2016 8:04 am
Forum: For Sale
Topic: Wealden Tool 1/2" Rabbeting cutter Large Series - SOLD
Replies: 0
Views: 388

Wealden Tool 1/2" Rabbeting cutter Large Series - SOLD

... with bearings to give 12.7 mm to 26 mm cut its in very good condition and comes with box and info sheet,just used once for further info go to wealden site. £30 delivered to uk mainland. http://www.wealdentool.com/cgi-bin/sh000001.pl?REFPAGE=http%3a%2f%2fwww%2ewealdentool%2ecom%2facatalog%2fRouter_Cutters_1%2ehtml&WD=t1717&SHOP=%20&PN=Online_Catalogue_Large_Series_214%2ehtml%23aT1717_2d1_2f2#aT1717_2d1_2f2
by RorieT
Sat Sep 12, 2015 9:26 am
Forum: Power Tools and Machinery
Topic: what size blade?
Replies: 8
Views: 871

Re: what size blade?

... look to buy my blades (screwfix etc) don't really allow for an easy time separating out the differences to select a blade… I'll have a look at Wealden and hopefully i'll get on better
by jake
Fri Sep 11, 2015 9:58 pm
Forum: Power Tools and Machinery
Topic: what size blade?
Replies: 8
Views: 871

Re: what size blade?

Blades for mitre saws should have a negative hook angle (teeth lean backwards, not forwards into the cut). TS blades should have positive hook angles.

Wealden do decent blades or Cutting Solutions who at least used to be on here.
by promhandicam
Tue Apr 28, 2015 11:47 pm
Forum: Woodworking
Topic: help 38mm hole cant drill
Replies: 47
Views: 3233

Re: help 38mm hole cant drill

Here is my attempt at a demo. Wealden 35mm hinge boring bit running at about 1000 rpm in an old fobco star drill press that I paid £50 for. Drilling into end grain unsorted red wood. Using the bit to fire the wood across the workshop is ...
by thatsnotafestool
Wed Mar 18, 2015 1:05 pm
Forum: Woodworking
Topic: how to reproduce this beading
Replies: 7
Views: 1044

Re: how to reproduce this beading

Can you not use this bearing guided cutter from Wealden ?
http://www.wealdentool.com/acatalog/Onl ... ge_70.html

beaded cutter.jpg
by promhandicam
Mon Mar 09, 2015 6:45 pm
Forum: Projects
Topic: Painted Wardrobes
Replies: 4
Views: 965

Re: Painted Wardrobes

Thanks for the comments. The doors were constructed using a wealden router cutter set, and you are correct that they do produce a 6mm groove. However I prefer the 'feel' of a 10mm panel - 6mm seems a bit flimsy, so I rebated all the panels (putting the ...
by Leveller2911
Sun Mar 01, 2015 7:47 pm
Forum: Finishing
Topic: Drawer pulls...
Replies: 6
Views: 813

Re: Drawer pulls...

Hi ft, I can't comment directly on your spray dilemma but I noticed your looking to use the Wealden cutter for the handle. I recently did a kitchen where the client wanted the same but when I did a sample of the handle we noticed the "undercut" is very shallow ...
by rhrwilliams
Thu Feb 19, 2015 6:55 am
Forum: Woodworking
Topic: Sash Cutters
Replies: 16
Views: 1533

Re: Sash Cutters

... . I'm not so much after advise of how to make the sash, I'm after advise on a good off the shelf profile and scribe for a spindle moulder . Wealden sell a number of variations but it's very difficult to see whats what from web. Here is something along the lines I'm after (this is a old georgian ...
by Oakfield
Mon Jan 26, 2015 8:06 am
Forum: Power Tools and Machinery
Topic: Why are router bits in inches?
Replies: 6
Views: 680

Re: Why are router bits in inches?

I agree about Wealden tools. They are a good product at a good price and the service first class. Although I wouldn't stress about using the same size cutter as sheet material as the thickness of material can vary sheet to sheet. ...
by jc2684
Sun Jan 25, 2015 8:49 pm
Forum: Power Tools and Machinery
Topic: Why are router bits in inches?
Replies: 6
Views: 680

Re: Why are router bits in inches?

Thanks for suggesting Wealden Tools, Steve and Leveller. I hadn't heard of them before, but I will be sure to order from there.

Jon
by Leveller2911
Sun Jan 25, 2015 8:42 pm
Forum: Power Tools and Machinery
Topic: Why are router bits in inches?
Replies: 6
Views: 680

Re: Why are router bits in inches?

+1 for Wealden Tools.. I aso have no connection with them apart from living about 20 miles away from them. Decent quality tooling and good service.....
by promhandicam
Sun Jan 25, 2015 5:09 pm
Forum: Power Tools and Machinery
Topic: Why are router bits in inches?
Replies: 6
Views: 680

Re: Why are router bits in inches?

... I suspect that the rutlands bits you linked to are imported from the USA where they cling on to imperial rather than using metric. Have a look at Wealden Tool Company for router bits where you will find a wide selection of good quality bits in metric (and some imperial) sizes. I have no connection ...
by promhandicam
Wed Sep 10, 2014 11:04 pm
Forum: Woodworking
Topic: Replacement kitchen unit door ideas please
Replies: 4
Views: 1168

Re: Replacement kitchen unit door ideas please

A similar idea would be to use a finger pull cutter to make a profile in the edge of the door / drawer front - one like this from Wealden http://www.wealdentool.com/acatalog/Online_Catalogue_Large_Pull_127.html I see that they are out of stock - if you want to borrow one I'd be happy to ...
by JonR
Wed Aug 06, 2014 7:22 pm
Forum: Power Tools and Machinery
Topic: Sawmills in Weald area of Kent
Replies: 2
Views: 679

Re: Sawmills in Weald area of Kent

... hes a nice fella and may get you sorted , how do i know about him well i went there with by lad to discuss him doing a course there, you also have Wealden Oak in Edenbridge they may re-saw your Oak for you, good luck.
by Roger-M
Wed Aug 06, 2014 2:01 pm
Forum: Woodworking
Topic: Odd Slot!!
Replies: 7
Views: 1131

Re: Odd Slot!!

... and use a slot cutter rather than a straight one - something like this . As a matter of interest, where will you get your dovetail cutter from as Wealden , who are always my first port of call, do not do one that small. However, they do groovers down to 1.5mm so perhaps you could get (say) a 3mm ...
by ondablade
Tue Apr 01, 2014 11:35 pm
Forum: Woodworking
Topic: CNC'ing Acrylic
Replies: 4
Views: 771

Re: CNC'ing Acrylic

... false; https://www.tapplastics.com/uploads/pdf/Tech%20Data-Routing.pdf" onclick="window.open(this.href);return false; Maybe the likes of Wealden and similar in the UK too? Either way a bit of digging might surface their recommendations for both cutter types and feeds etc.
by tusses
Fri Mar 07, 2014 12:29 pm
Forum: Woodworking
Topic: Spindle cutters!
Replies: 30
Views: 2026

Re: Spindle cutters!

... you want. All my stock is profiled now and as a hammer chewer, I'm not sure when/if I'd need to be making similar doors again. As for the fancy Wealden cutters, I do have one of their crown moulding router cutters which works well in my router table for the curvy bit and the rest of the profile ...
by 9fingers
Fri Mar 07, 2014 12:17 pm
Forum: Woodworking
Topic: Spindle cutters!
Replies: 30
Views: 2026

Re: Spindle cutters!

... you want. All my stock is profiled now and as a hammer chewer, I'm not sure when/if I'd need to be making similar doors again. As for the fancy Wealden cutters, I do have one of their crown moulding router cutters which works well in my router table for the curvy bit and the rest of the profile ...
by thatsnotafestool
Fri Mar 07, 2014 10:13 am
Forum: Woodworking
Topic: Spindle cutters!
Replies: 30
Views: 2026

Re: Spindle cutters!

'cos they cost a bit more usually.

As a supplementary question, does anyone actually USE any of those weird arty-crafty profiles in the Wealden catalogue?
by PABLO123
Tue Mar 04, 2014 9:30 pm
Forum: Power Tools and Machinery
Topic: Whitehill vari angle head
Replies: 9
Views: 794

Re: Whitehill vari angle head

... it, I'm looking at the 60mm replaceable TCT bladed one. http://www.whitehill-tools.com/catalogue.php?pid=2691&cid=2&c2id=26 I see Wealden are doing the Trend version for a similar price in aluminium but am more inclined toward the steel Whitehill, or can anyone recommend another ...
by Doug
Mon Mar 03, 2014 4:32 pm
Forum: Power Tools and Machinery
Topic: Whitehill vari angle head
Replies: 9
Views: 794

Whitehill vari angle head

... it, I'm looking at the 60mm replaceable TCT bladed one. http://www.whitehill-tools.com/catalogue.php?pid=2691&cid=2&c2id=26 I see Wealden are doing the Trend version for a similar price in aluminium but am more inclined toward the steel Whitehill, or can anyone recommend another ...
by tusses
Sat Feb 08, 2014 7:39 pm
Forum: Power Tools and Machinery
Topic: Drum Sanders
Replies: 15
Views: 917

Re: Drum Sanders

I use wealden cutters £20 a pop :shock:

I use them till they struggle ... cuz I'm tight too :) :lol:

3mm spiral down cut for anthing up to 12mm thick. The upcut ones lifted the small parts up off the bed.
6mm upcut for the 18mm thick

I might try some chinese ones :)
by tusses
Mon Feb 03, 2014 10:07 pm
Forum: Woodworking
Topic: Acid Etch Sharpening ... ?
Replies: 12
Views: 954

Re: Acid Etch Sharpening ... ?

where ?

I don't know anyone that sharpens spiral bits ? I asked at wealden... computer said 'no' !
by pukka474
Thu Jan 16, 2014 7:31 pm
Forum: For Sale
Topic: FOR SALE: Table saw/router combo. PRICE REDUCED - SOLD
Replies: 5
Views: 1849

Re: FOR SALE: Table saw/router combo. PRICE REDUCED

... the sort of work I do, I rarely if ever use it, so it's in excellent condition. It comes complete with a couple of nice German TCT saw blades from Wealden. As well as the saw, the extension side has a router table built in, complete with a UJK router lift from Axminster (but not the router) and ...
by robos60
Sun Dec 15, 2013 11:07 am
Forum: For Sale
Topic: FOR SALE: Table saw/router combo. PRICE REDUCED - SOLD
Replies: 5
Views: 1849

FOR SALE: Table saw/router combo. PRICE REDUCED - SOLD

... the sort of work I do, I rarely if ever use it, so it's in excellent condition. It comes complete with a couple of nice German TCT saw blades from Wealden. As well as the saw, the extension side has a router table built in, complete with a UJK router lift from Axminster (but not the router) and ...
by tusses
Fri Jun 28, 2013 7:52 am
Forum: Power Tools and Machinery
Topic: CNC Cutters
Replies: 14
Views: 1253

Re: CNC Cutters

oh, and I use downcut spirals from wealden.
It helps keep the work on the bed as I don't have vacuum.
by mark270981
Thu Jun 27, 2013 7:59 am
Forum: Power Tools and Machinery
Topic: CNC Cutters
Replies: 14
Views: 1253

Re: CNC Cutters

... 18mm mdf. We use a 10mm cutter, but do 2 passes. Mark, I use 8mm up spiral, they remove less material with closer nesting, I get them from either Wealden tool or Appleby woodturning Cheers Paul, how many passes do they cut in on 18mm??
by cncpaul
Thu Jun 27, 2013 6:43 am
Forum: Power Tools and Machinery
Topic: CNC Cutters
Replies: 14
Views: 1253

Re: CNC Cutters

mark270981 wrote:Can anyone tell me what cutters they use and where they get them from for doing profile cuts in 18mm mdf.

We use a 10mm cutter, but do 2 passes.



Mark,

I use 8mm up spiral, they remove less material with closer nesting, I get them from either Wealden tool or Appleby woodturning
by Leveller2911
Sun Jun 16, 2013 8:07 pm
Forum: Woodworking
Topic: Sash Windows
Replies: 4
Views: 1694

Re: Sash Windows

... of brush pile and I use whichever fits the best. I router the stick on "pile carrier" into the stiles with a router cutter I bought from Wealden tools and have 3 different bearings which gives me a bit of flexibility if I don't get the meeting rail bevels spot on the correct width for ...
by lynx
Wed May 15, 2013 11:41 am
Forum: Power Tools and Machinery
Topic: Large plunger/mortising router bit?
Replies: 12
Views: 1370

Re: Large plunger/mortising router bit?

either way. Wealden tools for the cutters.
by thatsnotafestool
Fri Apr 26, 2013 5:46 pm
Forum: Power Tools and Machinery
Topic: Hammer
Replies: 112
Views: 12418

Re: Hammer

Good update. While browsing the Wealden site looking at spindle cutters they have a spiral planer http://www.wealdentool.com/acatalog/Online_Catalogue_Spiral_planer_609.html" onclick="window.open(this.href);return false; It looks identical ...

Go to advanced search